fiduciary

Author Topic: Graflex Project AKA "The Pain!"  (Read 8123 times)

0 Members and 1 Guest are viewing this topic.

Offline Lord Massia

  • Force User
  • ***
  • Posts: 102
  • Xbox Live gamertag: TBD x BULL3T
Re: Graflex Project AKA "The Pain!"
« Reply #15 on: March 01, 2009, 06:05:46 PM »
Man I want a graflex!!!  :'( Now Im mad since I just spend all my money on a new airsoft gun!! :'( >:( If I would've known I would have bought that from you in a heartbeat!!!!! :D :-\
Lightsaber collection:
1. The Serenity (aka Qui-Gon-Jinn's B.S. #8) Blue P4, US 2.1
2. MR Vader ANH Red lux III converted by Ultra Sabers
3. Ultra Sabers The Vagabond green lux III
4. Stock MR Luke ANH
5. Sink Tube saber Red lux III
6. MR Yoda
7. Ultra Sabers The Manticore red lux III

Offline Maximillian

  • FX-SABERS VIP
  • Experienced Force User
  • *
  • Posts: 448
  • Official FX-SABERS GRAFLEX ARMORY Guardian
Re: Graflex Project AKA "The Pain!"
« Reply #16 on: March 01, 2009, 06:56:18 PM »
That is fantastic work.  I hope my Graflex build goes as well.  The additional crystal always makes these things pop.
Man I want a graflex!!!  :'( Now Im mad since I just spend all my money on a new airsoft gun!! :'( >:( If I would've known I would have bought that from you in a heartbeat!!!!! :D :-\

Thanks guys! There are a few details I would eventually like to change but overall I think it turned out well using stock parts (except the Corbins Board). This project could've been better if I had the CF 4.0 board. But it was a fun experiment!

Offline Gabywan

  • Master Force User
  • *****
  • Posts: 945
  • Que nunca muera el niņo que llevamos adentro...
Re: Graflex Project AKA "The Pain!"
« Reply #17 on: March 01, 2009, 07:06:07 PM »
Hi Darth!!!
Really it is a very good work!!! :D
I am going to bear in mind the cicuito RGB, I was for using a flashing led for my crystal chamber, in blue color.
Your work has given me new ideas. ::)
Thank you bro!! :D
Gaby!

Offline Maximillian

  • FX-SABERS VIP
  • Experienced Force User
  • *
  • Posts: 448
  • Official FX-SABERS GRAFLEX ARMORY Guardian
Re: Graflex Project AKA "The Pain!"
« Reply #18 on: March 01, 2009, 07:17:10 PM »
Your welcome Gaby!!!  Any good electronics store has the LED. They actually refer it as a "7 color" led. It has no spec sheet on it though so if you want, I can help you hook it up. They are only a couple of bucks and run on very low voltage. (so resisters are a must). Lemme know and thanks!

Offline Gabywan

  • Master Force User
  • *****
  • Posts: 945
  • Que nunca muera el niņo que llevamos adentro...
Re: Graflex Project AKA "The Pain!"
« Reply #19 on: March 01, 2009, 08:29:36 PM »
Have not I understood very well, these leds do not need resistors? ???

Offline Gabywan

  • Master Force User
  • *****
  • Posts: 945
  • Que nunca muera el niņo que llevamos adentro...
Re: Graflex Project AKA "The Pain!"
« Reply #20 on: March 02, 2009, 03:05:36 AM »
I do not know of electronics.... I always thought that an electrical resistecia was necessary along with the led so that this one does not work hard.

Offline Maximillian

  • FX-SABERS VIP
  • Experienced Force User
  • *
  • Posts: 448
  • Official FX-SABERS GRAFLEX ARMORY Guardian
Re: Graflex Project AKA "The Pain!"
« Reply #21 on: March 02, 2009, 04:28:25 AM »
Have not I understood very well, these leds do not need resistors? ???

Im sorry for not being clear. Yes they need some resisting. specially if you are running anything over 3.2V

Offline Gabywan

  • Master Force User
  • *****
  • Posts: 945
  • Que nunca muera el niņo que llevamos adentro...
Re: Graflex Project AKA "The Pain!"
« Reply #22 on: March 02, 2009, 05:15:01 AM »
Forgive me you!!...  :-[
My problem is that I do not have good English and sometimes I understand badly the things,... :-\
Thanks friend :)

Offline Maximillian

  • FX-SABERS VIP
  • Experienced Force User
  • *
  • Posts: 448
  • Official FX-SABERS GRAFLEX ARMORY Guardian
Re: Graflex Project AKA "The Pain!"
« Reply #23 on: March 02, 2009, 07:18:27 AM »
Anytime Gaby!