0 Members and 1 Guest are viewing this topic.
Sound Transferring Electronic Velocity Effects SystemThe New Ultrasound 2.5 based on the same compact 1 x 2 x 0.15 inch platformthe new 2.5 with faster more powerful components and new operating systemoffers more features, improved performance and improved sounds.The New Ultrasound 2.5 features:Supports two accent LEDsSupports Multiple Luxeon LED types including:Single button/switch operation and set-up.Luxeon, 3watt, 5watt, K2, Luxeon 3 Red, and a New Luxeon 3 overdrive selection.A New Clash Lock Effect that rapidly pulses the LED for that classic blade lock upor cutting through objects look.5 different Blade frequencies ranging from a solid blade through slow to fast pulse/flickering.Improved and user adjustable sensitivity for Clash detection and Motion Detection.New and improved Clash and Motion sounds.New and improved sound mixing and playback.Improved motion and sound registration providing different sounds for thecorresponding slow, moderate, and faster movements.Two Selectable Volume levels to better accommodate different speaker outputs forclear and better sound projection.ULTRASOUND OPERATION INSTRUCTIONS.This board uses a momentary tactile switch for operation.1. Tap the button once to turn the saber on.2. Hold the switch down for 2.5 seconds to turn the saber off.3. Push button for Clash/Lock Effect.After saber is activated (in on mode) the user can press once to activate a fast flicker effectUser can again press once to deactivate fast flicker and return to standard operation.Main Menu: Set-up Navigation1. With Saber turned off and batteries installed hold the button down to enter the setup menu.You’ll know you’re in the menu because the board will tell you (it talks).2. Tap the button to go through the choices.After you hear the board say the LED type your using or Level of operation desiredhold the button down to select it.Select Luxeon type..."Luxeon 3" / "Luxeon 3 Red" / "Luxeon 5" / "Luxeon K2" / "Luxeon 3 Overdrive"Select Blade Frequency..."Constant On 1" / "Slowest Pulse 2" / " 3" / " 4" / "Fastest Pulse 5"Select Sound Level..."Level 1" Low / "Level 2" HighSelect impact sensitivity level..."lowest sensitivity 1" / "2" / "3" / "4" / "highest sensitivity 5"Select Motion sensitivity level..."lowest sensitivity 1" / "2" / "3" / "4" / "highest sensitivity 5"Your settings have been saved!4. The saber will exit the setup menu after the blade mode selections.Installation specifications and requirements.LED choices:1. Luxeon 3 all colors white/blue/green (1000mah)2. Luxeon 3 red/amber/red-orange (1400mah)3. Luxeon 5 (850mah)4. Luxeon K2 (1500mah)5. Luxeon 3 Overdrive (1200mah)IMPORTANT! (be sure to select the correct LED type installed in your saber)Battery input voltage:Maximum for board = 9.6VMinimum/Maximum for Luxeon 3, K2, P4 = 4.5V / 7.2V (6V recommended)Minimum/Maximum for Luxeon 3,P4 Red/Amber = 4.8V / 6.0VMinimum for Luxeon 5 = 7.2VIMPORTANT! (be sure to use the correct voltage/power with corresponding LED type)Switch Type.Momentary switch required (switch bounce issue has been resolved)Mounting and Installation Recommendations.Soundboard should be mounted/secured to a non metal surface.Plastic Tubing or sleeving is recommended for lining the inner wall of your saber and or tosurround the board preventing and foreign metals to accidentally come in contact with theboard while power is applied)A plastic mounting plate/case is recommended for attaching to an internal chassis or byother means of securing it in the hilt to keep it stationary for proper gesture recognition.Safety and Precautions:DO NOT leave batteries in Saber while not in use for long periods that would allowthe batteries to completely drain.REVERSE VOLTAGE or improper LOW VOLTAGE can damage the electronics.Only Use the specified batteries and observe all battery precautions.FOLLOW CHARGING INSTRUCTIONS CAREFULLY FOR LITHIUM ION BATTERIESACCORDING TO CHARGER INSTRUCTIONS.** Photosensitive epilepsy warning.Photosensitive epilepsy is the name given to epilepsy in which all, or almost all, seizuresare provoked by flashing or flickering light, or some shapes or patterns. Both natural andartificial light may trigger seizures. Various types of seizure may be triggered by flickering light.