fiduciary
« previous next »
[1] Go Down

Author Topic: Problem with Prizm 5  (Read 2038 times)

0 Members and 1 Guest are viewing this topic.

Offline maverick10240

  • No Force
  • *
  • Posts: 8
  • Um...Hello?
Problem with Prizm 5
« on: July 26, 2017, 11:07:03 AM »
Hi Saberworld,
I just wired my new Prizm V5 and everything was fine!
But: I tuned some saberfonts and load them on the sd card from the Prizm. Because of bad access to my sd card I broak the card  :cry:
Then I bought a new one and mount it successfully. The saber started as always.
But: after a few seconds of normal sound the sound went to a scratching sound and every second a little more...
I changed the speaker and have the same problem again.
Is there a possibility to destroy the amp or something else?

Please help me...

Thank You and best regards

Benjamin
Logged

Offline erv

  • Plecter Labs Inc. "Keeper of the Buttered Toast"
  • Manufacturer
  • Master Force User
  • *
  • Posts: 4920
  • Formerly known as Irvin PLECTER
    • Plecter Labs - Props Electronics
Re: Problem with Prizm 5
« Reply #1 on: July 26, 2017, 11:12:22 AM »
[edited]New NO amplifier damage in my opinion but breaking the card probably been to the SD card socket as well and what you hear is the card is in contact with the socket Reading to corrupted samples being read
« Last Edit: July 27, 2017, 06:26:25 AM by erv »
Logged

Offline maverick10240

  • No Force
  • *
  • Posts: 8
  • Um...Hello?
Re: Problem with Prizm 5
« Reply #2 on: July 26, 2017, 11:14:47 AM »
Thank you... What can I do? Can You repair it?
Thank you for answering.
« Last Edit: July 26, 2017, 11:30:22 AM by maverick10240 »
Logged

Offline erv

  • Plecter Labs Inc. "Keeper of the Buttered Toast"
  • Manufacturer
  • Master Force User
  • *
  • Posts: 4920
  • Formerly known as Irvin PLECTER
    • Plecter Labs - Props Electronics
Re: Problem with Prizm 5
« Reply #3 on: July 27, 2017, 06:28:49 AM »
where are you located ? I've edited my post above, phone typo (sorry). If no PCB trace was ripped off in the case the holder was lifted, the socket can be changed). I take care of repairs in the EU, and chewbacca / Michael (member here) does repairs in the USA / North america
Logged

Offline maverick10240

  • No Force
  • *
  • Posts: 8
  • Um...Hello?
Re: Problem with Prizm 5
« Reply #4 on: July 27, 2017, 11:41:06 AM »
Hi,
I'm from Germany. I will dismantle the board this weekend and then I Contact You again. Thank You for Your offer! Cheers
Logged

Offline maverick10240

  • No Force
  • *
  • Posts: 8
  • Um...Hello?
Re: Problem with Prizm 5
« Reply #5 on: September 04, 2017, 03:10:19 AM »
Hi Erv,
no I got the Prizm in my hand and I can see nothing on it. Can I send it to you for a check? Please give me some advice... Thank you and best regards, Benjamin
Logged

Offline erv

  • Plecter Labs Inc. "Keeper of the Buttered Toast"
  • Manufacturer
  • Master Force User
  • *
  • Posts: 4920
  • Formerly known as Irvin PLECTER
    • Plecter Labs - Props Electronics
Re: Problem with Prizm 5
« Reply #6 on: September 04, 2017, 03:13:28 AM »
as usual, with no pictures posted it's difficult to answer. A video would help too. Thanks
Logged

Offline maverick10240

  • No Force
  • *
  • Posts: 8
  • Um...Hello?
Re: Problem with Prizm 5
« Reply #7 on: September 04, 2017, 05:09:38 AM »
Hi,
I think a picture make no sense, because of no visible changes on the board. I didn´t make a video before I dismantled the saber  :cry:. The board started normal and after a few seconds came a scratching noise which is going louder and louder. If you want I can mount the saber again and make a video... should I
Logged

Offline erv

  • Plecter Labs Inc. "Keeper of the Buttered Toast"
  • Manufacturer
  • Master Force User
  • *
  • Posts: 4920
  • Formerly known as Irvin PLECTER
    • Plecter Labs - Props Electronics
Re: Problem with Prizm 5
« Reply #8 on: September 04, 2017, 05:30:26 AM »
please assemble the board with just a speaker, switch and battery, then make a video, thank
Logged

Offline maverick10240

  • No Force
  • *
  • Posts: 8
  • Um...Hello?
Re: Problem with Prizm 5
« Reply #9 on: September 04, 2017, 05:43:11 AM »
Yes Sir!
Logged

Offline maverick10240

  • No Force
  • *
  • Posts: 8
  • Um...Hello?
Re: Problem with Prizm 5
« Reply #10 on: September 29, 2017, 04:03:01 AM »
By the way: Problem is solved, battery was low... Thanks to Erv!
Logged
[1] Go Up
« previous next »
 

retrousse