Help with cfx

[pipster79]

I just got my cfx yesterday, trying to wire up for a single led but I'm getting no power on any of the hb led outputs, checked all the color profiles and set them all to Max but still no power. Did I get a dud?

[erv]

strippower param (0000)

[pipster79]

That worked there's power now but it's same as power source, so if using 7.4v pack it doesn't limit the voltage like the old cf versions?

[K-2SO]

That worked there's power now but it's same as power source, so if using 7.4v pack it doesn't limit the voltage like the old cf versions?

Nope. If you weren’t using the right resistors for 7.4V, the possibility exists that you might have fried a LED .

[NeoSephiroth]

I've got the same problem. But only with firmwares higher than 10.001, up to 10.004E.
Using 3,7V battery, so I did not kill my LED.
When I downgrade the firmware to 10.002, everything works fine. Any suggestions?

Btw., here's my config:

//CF-X Configuration
debug=0
logport=0
vol=100
menuvol=25
menugest=0
beep=25
muteb=0
muteoff=0
sleep=50000
deep=300000
qkignite=0
grav=-500
valsnd=1
switch=2
offp=1
offd=75
onp=0
ond=20
swing_flow=360
clash_flow=300
spin_flow=400
smooth_flow=1000
lockup=300
loop=1
shuffle=2
plilh=3400,4200
omnisense=2000
ledstrip=0
plistrip=0
tridentstrip=0
dragstrip=0
ls1_timings=42,84,24,1,3
ls2_timings=42,84,24,1,3

## Motion Settings
gate=40
smooth_gate=40
hswing=450
hclash=750
hstab=500
hspin=750
htwist=350
hdrag=0,400
htemp=40
spectrum_mode=0
spectrum_axis=0
field=10,10,10


[profile=0]
wakeup=1
randc=0
blastp=0
random=2
pom=0
pof=0
poi=0
magic=0
saberlock=0
tridenton=0
tridentoff=0
tridentfx=0
tridentflk=0
tridentquick=0
blastm=0
randb=3
shmrd=350
shmrp=15
shmrr=25
shmr%=50,99
focd=350
focp=25
focr=30
foc%=50,99
focl=1
focb=1
focf1=1
focf2=1
focf3=0
qon=0
qoff=0
fade=0
flks=5
flkd=25
flkon=1
flkoff=1
pulsed=50
pulsel=5
lsfadeon=1
lsfadeoff=1
lightstick=0
unstable=0
hcool=70
lcool=0
sparkf=120
sparkd=10
drift=1
mapb=100
mapc=70
omnisabers=0
sbolt=8,20
dbolt=40,810
lbolt=15,30
fbolt=1
rbolt=10

[erv]

strippower=0000

[NeoSephiroth]

I digged a bit deeper because it was still not working.
bladepower=100 was missing. Now it works. Thx.

[yossh55]

i need help!

Today I made Saber with CFX
When I turn on the power, it starts without any problem, but it restarts every 30 seconds
Please give me advice

[erv]

When I turn on the power, it starts without any problem, but it restarts every 30 seconds

charge your battery

[yossh55]

When I turn on the power, it starts without any problem, but it restarts every 30 seconds

charge your battery

I tried three Keep Power 18650 15A but got the same result

[K-2SO]

Are you moving it around when it shuts off?

[yossh55]

Are you moving it around when it shuts off?

No
Boot sounds every 30 seconds without any action

[K-2SO]

It sounds like you have a short or ground somewhere in your wiring.

[yossh55]

It sounds like you have a short or ground somewhere in your wiring.

When I changed only CFX with the same wiring, it worked without any problem.
I think there is a problem with the foundation, but I do not know where the problem is

[erv]

obviously without any macro picture of your board, it's hard to diagnose anything. You should also check your voltage map. It's probably a wiring issue as stated above