I got this one pretty much all buttoned up last night and today, here's how it went....
I started to solder up the soundboard last night, then my camera's battery died, so I didn't get much in the way of pictures until I had it pretty much ready to install:
You can see the recharge port in there from this angle....it will allow for charging batteries in the saber, but it's not really necessary, since the batteries are removable. They are also individually protected, so they may not get an even charge if you were to charge them in the saber:
Here you can see the wires for the switch and the plug for the main blade led. It'll be able to change the led for another color, but it will have to have another modified heat sink to do so.
To secure the sound board to the chassis, I used a few pieces of double sided foam tape and then a thin strip of 1" heat shrink tubing:
This is safe to do with this sound board since it's not totally covered and will bleed off any excess heat just fine. The PC boards generally don't get very hot anyway.
With that done, I was ready to install the sound board chassis and the recharge port/aux switch assembly....I only really have one shot at getting this in there correctly:
This set up works great for mounting these parts without any nuts on the outside of the hilt, but if something goes wrong, it can be a real PITA to get out again....
I had made sure to add enough wire for the speaker and battery pack so it'll reach the end of the hilt:
So far, so good....
I used a flat bladed screw driver to work the c-clip into position, first snapping the aux button into place, then the recharge port:
Success:
Both parts snapped right into place and are nice and secure!
There's plenty of wire to add the battery pack and speaker:
But I'll add the main switch first:
These wires are for the the switch led and the activation button. White is the actual switch lead, orange is the positive for the switch led and is wired to the PC to led pad 1 (it will blink when power is supplied to the saber, but it's turned off) and the gray wire is the small signal ground from the accent led pads. I'll use this for the ground for the switch, as well.
I shortened the wires up a bit, then added a jumper to the switch's negative terminal for the led, and the switch negative:
Then I added the negative lead from the board.
Next up, the positive for the switch led:
I added the white wire for the activation switch, slipped some small pieces of heat shrink tubing over the tabs, and pushed the switch into the saber:
The nut was already in there on the wires, so all I had to do next was slip it over the threads on the switch, and then tighten it up:
Now it's time to add the battery pack:
The first thing to do was thread the speaker wires through the battery holder:
Looks like there's just enough wire to work without having to shorten it.
I made the connections at the battery pack and heat shrunk them:
Soldered the leads to the speaker:
Fit it into the speaker mount:
I also glued it to the speaker mount by using a blob of hot glue on the back of the speaker. No pics of that, had to have both hands....;)
I installed a couple of Trustfire Li-Ion batteries, and heard the boot sound again, "This party's over." :) Then the activation switch led began blinking, right on cue:
I powered the saber down, inserted the kill plug into the recharge port, and added the led from CS-35 again and powered the saber back up:
Not bad....not as purple as I'd like it though....
I added the pommel so I it wouldn't let the battery pack fall out, and shot a little video:
It's pretty loud, but I think it'll quiet down a bit once I add the actual led and the blade holder.
Here's how it looks as it is right now:
It still has some cosmetic parts to add, but it's almost done, and will actually be usable later today. ;)
I moved on to the actual led for this one:
this is a 3-watt ( I hate that term, it's really accurate, but it's what it's called on the site I got it from) RGB....I'll put the red and blue in a parallel connection and resistor the red to make purple/violet.
I added an adhesive pad first:
This not only holds the led on the heat sink, but aids in heat transfer, and insulates the aluminum base the led is attached to from the copper heat sink.
I wired it up on a temporary basis, then added the lens and the blade holder, and checked it for color:
Not bad....I like! It's a nice shade of purple/violet that isn't too hot pink looking. I think it'll work.
I finalized the wiring on the led, then installed it in the saber:
This is a little tricky to do, since the main switch is right there in the way for the led's connector. I had to slip it by the switch body, but it fit just fine, so I added the lens and holder:
I added the blade holder and my Trans-White blade from CS-X and powered it up:
nice!
I adjusted the camera a bit and took another that shows the blade a bit more true to color:
I think that'll do!
I also shot a little pre-review video:
Now to get that Graflex button ordered and make up the t-track grips for the blade holder.